Crafting A Ring Holder For Your Wedding: Creative Diy Ideas

There are many creative ways to make a ring holder for a wedding. For those who enjoy reading, a vintage book can be used to create a ring holder. This involves hollowing out a small box in the book and slipping a ribbon through the cut-out to hold the rings. Another option is to use oven-baked clay to create a ring bowl or dish. This involves rolling out the clay, pressing a pattern into it, and baking it into shape. A more natural approach could be to use hay, wood, grass, or flowers to create a ring holder.

How to make a ring holder dish from clay

A clay ring holder dish is a great way to keep your rings safe and is a fun, easy craft to make for yourself or as a gift. Here is a step-by-step guide on how to make a ring holder dish from clay.

Materials:

• Oven-bake clay in your choice of colours (white, grey, black, and a colour of your choice)
• X-Acto knife or plastic clay knife
• A small bowl or baking ramekin (oven-safe)
• Gold paint and a small paintbrush
• Silicone rolling pin or a large round jar
• A large can or jar to trace around
• Glaze to seal the dish (optional)

Method:

Start by rolling each colour of clay you want to use into a snake, about 5 inches long. You will need enough clay to roll out a 6-inch circle, so combine the colours into one big roll and twist them together. Roll the large twist into a longer snake, folding and twisting until the colours combine and create a marbled pattern.

Next, use a silicone rolling pin or a glass jar to roll out the clay into a 1/4-inch thick circle. Use a round item about 6 inches wide as a template and cut out your dish circle with a knife.

Place the circle gently into an oven-safe bowl or ramekin that is slightly smaller, so the clay sags a little in the centre to create a dish shape. Bake according to the instructions on your clay package.

Once baked, let the clay cool completely before removing it from the bowl. Paint the rim of the dish with gold paint and allow it to dry. You can also add a glaze to seal the dish and give it a glossy finish, but this is optional.

Alternative Method:

An alternative method is to use air-dry clay instead of oven-bake clay. Roll a small ball of clay between your hands to create a cone shape, ensuring the base is flat so it will stand upright. The cone should be about 8cm high and 2cm wide. Leave the clay to dry completely, then lightly sand it down to achieve a smooth surface.

Paint the cone white and let it dry. Decorate it with washi tape and paint, then carefully remove the tape once the paint is dry. Add a coat of gloss varnish to seal the paint and make it more durable.

Your clay ring holder dish is now complete! These dishes can be personalised and make great gifts for friends and family.

How to make a ring holder from a vintage book

If you're looking for a unique ring holder for your wedding, consider making one from a vintage book. This project is easy to do and will only take about ten minutes to complete. It's a great way to incorporate a favourite book or one that holds special meaning for you and your partner. Here's a step-by-step guide on how to make a ring holder from a vintage book.

Materials:

• Vintage book
• Ruler
• Pencil
• X-acto knife
• Ribbon

Instructions:

Step 1: Choose a book that is meaningful to you and your partner or one that fits your wedding colours.

Step 2: Open the book to almost halfway through, a little less than half, and draw a small two-inch box in the centre-right area, towards the outside of the book.

Step 3: Using a straightedge and an X-acto knife, carefully cut along the lines you drew. Press down hard and go over each line multiple times to cut through as many layers as possible. Repeat this step several times to create a deep hollow for your rings.

Step 4: Pop out the paper to reveal your hollowed-out box.

Step 5: Slip a ribbon through the cut box, making sure to go through all the pages that are cut.

Step 6: Place the rings onto the ribbon and rest them inside the hollowed-out box. Close the book and tie the ribbon into a bow.

And that's it! You now have a unique and personalised ring holder for your wedding, perfect for displaying your rings during the ceremony and keeping them safe.

Optional: You can also create a small ring pillow to place inside the hollowed-out book. To make the pillow, cut two squares of fabric and sew a piece of ribbon on the right side of one square. Place the two squares together, sew around the edges, leaving an opening, and then turn the pillow right side out. Stuff the pillow with filling and sew it closed.

How to make a traditional ring pillow

A ring pillow is a vessel that helps transport the wedding rings down the aisle. It often features ribbons that can be tied to the rings for added security. The traditional ring pillow is an 8-inch by 8-inch square, but you can choose a different size depending on the age and size of your ring bearer.

Select your fabric and cut out two squares.

Choose a fabric that matches your wedding colours and theme. It can be satin, cotton, burlap, etc. Cut out two squares of fabric, each measuring 10 inches by 10 inches (25 cm by 25 cm). If you want a different-sized pillow, remember to add a 1/2-inch (1.3 cm) seam to the length and width.

Stack the squares with right sides together and secure with pins.

Place one square with the right side facing up. Put the second square on top, with the right side facing down. Secure the edges with pins.

Sew three edges, leaving one open.

Sew three of the edges with a 1/4-inch (0.64 cm) seam allowance. You can use a sewing machine or sew it by hand. Use a straight stitch and a thread colour that matches the fabric. If you don't know how to sew, you can use hot glue or fabric glue to secure the edges.

Trim the corners.

Trimming the corners is optional but recommended as it reduces bulk and helps the pillow look neater. Cut as close to the stitching as possible without cutting the thread. Be sure to clip the corners of the open edge to make it easier to sew shut later.

Turn the pillow right side out and stuff it.

Flip the corners into the pillow, then pull them out through the opening. Use a blunt, pointy object like a knitting needle or pencil to push the corners out further. Stuff the pillow with polyester filling, foam, or a blank ring pillow.

Close the open seam.

Push the stuffing into the pillow so that it doesn't stick out. Fold the raw edges of the opening inward by 1/4 inch (0.64 cm) and secure them with pins. Sew the opening shut by hand with a ladder stitch, then remove the pins. Alternatively, you can use hot glue or fabric glue to close the seam.

Attach a string to a ribbon with a slipknot.

Choose a ribbon and string that match your pillow. Fold the string in half to form a loop behind the ribbon. Pull the ends of the string to make a knot around the ribbon, then tighten the knot by tugging on the ends. Centre the knot by sliding it along the ribbon.

Form the ribbon into a bow.

Take the left and right ends of the ribbon and fold them into loops. Cross the left loop over the right, then thread it through the gap you've created. Pull on the loops to tighten the bow. Leave the strings out of the bow.

Secure the bow to the pillow.

Position the bow in the middle of the pillow and sew or glue it in place. Make sure the strings and tails of the bow hang below the loop.

Trim and singe the ribbon and strings.

Cut the ribbon and strings to your desired length. If the material is fraying, use a flame to singe the ends.

Tie the rings to the strings.

Thread both rings onto one of the strings, then tie both strings into a knot or a bow.

And there you have it—a traditional ring pillow for your wedding!

How to make a ring bowl from oven-baked clay

Making a ring bowl from oven-baked clay is a fun and easy project that you can do yourself as a unique ring holder for your wedding. Here is a step-by-step guide on how to create your own ring bowl:

Materials:

First, gather your materials. You will need oven-baked clay, such as Sculpey, in your preferred colour(s). You can choose a single colour or multiple colours for a marbled effect. Other materials include a small oven-safe bowl or ramekin, parchment paper or wax paper, a rolling pin, a cookie cutter or lid to cut out your shape, paint and a paintbrush (optional), and sandpaper (optional).

Shaping the Clay:

To start, take your clay and roll it into a ball. Place the ball on a piece of parchment or wax paper. Use a rolling pin to roll out the clay to a thickness of approximately 1/4 inch. If you want to add a pattern or texture to your bowl, you can use a variety of techniques. For example, you can place a fabric doily on the rolled-out clay and roll over it with the rolling pin, or use stamps to create an impression.

Cutting and Baking:

Once you're happy with the pattern, it's time to cut out your shape. Use a lid or a cookie cutter to cut a circle out of the clay, slightly larger than the size of your oven-safe bowl. Position your circle of clay gently into the bowl, allowing it to sag a little in the centre to create a dish shape. Follow the baking instructions on your clay package; typically, this involves baking at a temperature of around 275°F for about 15- 30 minutes.

Finishing Touches:

After removing the bowl from the oven, let the clay cool completely before carefully turning the bowl upside down and removing the clay dish. If you want to smooth the edges of your bowl, you can use sandpaper, but be sure to sand it when it is wet to avoid inhaling clay particles. At this point, you can also add paint or glaze to decorate your ring bowl, although this step is entirely optional.

And there you have it! Your very own handmade ring bowl, perfect for holding your rings on your wedding day and a beautiful keepsake to cherish afterwards.

How to make a ring holder from a jewellery box

A jewellery box is a decorative storage container for earrings, necklaces, and rings. While some boxes come with compartments and drawers, others may not have cushioned ring holders. Here is a guide on how to make a ring holder from a jewellery box:

Step 1: Measure the compartment

First, measure the compartment in your jewellery box where you want to keep your rings. This will be the space in which you will place your ring rollers.

Step 2: Cut a piece of satin fabric

Cut a piece of satin or another fabric of your choice to the dimensions of the compartment you measured. This will be the base of your ring holder.

Step 3: Prepare flexible foam hair rollers

Choose several flexible foam hair rollers of the same diameter. Remove any fasteners from the ends of the rollers. If the rollers are too long, cut them to fit snugly into the ring compartment with a pair of large scissors. You want the rollers to fit side by side inside the compartment, filling it completely, with the rollers slightly mashed together but not springing out of the box.

Step 4: Cut faux suede fabric

Cut a piece of faux suede fabric the same length as the rollers. Make it wide enough to cover a roller when wrapped around the outside with a 1/4 inch or less overlap where the edges meet. Cut a piece of faux suede the same size for each roller.

Step 5: Wrap the rollers

Remove the rollers from the ring compartment. Wrap each roller in a piece of faux suede and glue it in place along the seam with fabric glue. Put a bead of glue on the outside of the faux suede along the seam, and press it along one edge of the satin piece. Repeat for the rest of the rollers, placing them side by side on the satin so that they press against each other.

Step 6: Place the rollers in the compartment

When you put the satin on the bottom of your ring compartment, the rollers should be slightly pressed together, offering resistance when you press a ring band between them. Set the satin and roller combination into the ring compartment of your jewellery box, and you're ready to organise your rings!

Tips

You can use any fabric for the bottom piece and roller coverings, but a tacky fabric, not a slippery one, works best for the roller cover pieces.

Frequently asked questions