Wedding Band Size: Finding The Perfect Fit

There are several ways to find out your wedding band size. You can use a ring size chart, a piece of string, or a plastic ring sizer. You can also measure the inside of a ring you already own. If you're measuring at home, it's important to do so at the end of the day when your fingers are warm, as finger size changes depending on the time of day and the weather. It's also a good idea to measure your ring size a few times to ensure accuracy.

Measure with a ring size chart and a ring you already have

If you already have a ring that fits your ring finger, you can use a ring size chart to find your size. Here's how to do it:

Step 1: Find a ring that fits your ring finger

Choose a ring that you wear on your left ring finger, which is the finger you plan on wearing your wedding band on. This will ensure the most accurate sizing.

Step 2: Print out a ring size chart

Search online for a printable ring size chart. Make sure that the guide is printed to scale by selecting "Scale 100%" when printing. You want to ensure that the chart is the actual size so that you can get an accurate measurement.

Step 3: Place your ring on the chart

Place your ring over the circles on the chart, lining up the inside edges of the ring to the circle that best matches its size. If the ring falls between two sizes, choose the larger one.

Step 4: Refer to the corresponding size

Look at the ring size that corresponds to the circle you chose on the chart. This will give you your ring size.

It's important to note that ring sizes can vary slightly depending on the region and country. The methods described above are based on US ring sizing, which ranges from size 3 to 13 for adults, with half and quarter sizes in between. The sizes are measured in inches or millimetres based on the ring's diameter or circumference.

Measure with a paper strip

To measure your wedding band size with a paper strip, follow these steps:

• Cut a strip of paper.
• Wrap the paper strip snugly around the base of your finger. Remember not to wrap it too tightly, or it will be difficult to get the ring over your knuckle. Also, keep in mind that your fingers will swell, so leave a little room.
• Mark the point on the paper strip where it completes the circle. It shouldn't be too tight or too loose.
• Measure the length of the paper strip with a ruler or tape measure. This will give you the circumference of your finger.
• Use a ring size conversion chart to find your ring size based on the circumference measurement. Look for the "inside circumference" measurement on the chart.

If you are in between sizes, it is generally recommended to go up a size, especially if you live in a warm environment, as heat can cause your fingers to swell.

Measure with a piece of string

Measuring your ring size with a piece of string is a simple and creative way to find the right fit. Here is a step-by-step guide:

Firstly, cut a piece of non-stretchy string. It is important to use non-stretchy string as stretchy string can lead to inaccurate measurements. You can also use dental floss or a strip of paper if you prefer.

Next, wrap the string around the base of your finger. It should fit snugly, but remember not to wrap it too tightly or you will have trouble getting the ring over your knuckle. Your fingers will also swell, so be sure to leave a little room for the ring.

Mark the point on the string where it completes the circle. It shouldn't be too tight or too loose.

Now, measure the length of the string with a ruler or tape measure. This will give you the circumference of your finger.

Finally, use a ring size chart to find your ring size. The length you measured can be compared to the standard ring sizes on the chart. Divide the circumference by pi (3.14) to get the diameter of your finger. Remember to choose the larger size if your finger is between two sizes.

It is worth noting that string measurements may not always be completely accurate due to factors such as printer settings or the stretch of the string. Therefore, it is recommended to use multiple methods to measure your ring size for added precision.

Measure with a plastic ring sizer

Using a plastic ring sizer is a straightforward way to check your ring size from the comfort of your home. Here's a step-by-step guide on how to use one:

Clean and Dry Your Hand

Start by cleaning your hand with room-temperature water, and then dry it properly. This ensures that your finger is in its standard state and isn't swollen due to heat or any residue.

Insert the Ring Sizer

Insert the end of the ring sizer into the buckle to form a loop. It's just like making a belt!

Put the Loop on Your Finger

Place the loop on the finger you want to size. This is usually the fourth finger on your left hand, but it can vary based on your preference and culture.

Tighten the Loop

Tighten the loop around your finger until it is snug but not too tight. It should be tight enough so that it won't fall off your finger, but it shouldn't be so tight that it hurts.

Clench Your Finger

Clench your finger while the ring sizer is on. This is an important step as the ring sizer may adjust slightly, and that is fine.

Try to Remove the Ring Sizer

Without loosening the belt, try to remove the ring sizer by sliding it over your knuckle. It should be able to come on and off your finger with some resistance. If it's too tight or too loose, adjust the sizing accordingly.

Read the Measurement

Carefully read the number on the belt to determine your ring size. The ring sizer measures in half sizes, but some companies can accommodate quarter and three-quarter sizes as well. The arrow on the buckle will point towards a number or between two numbers, indicating your size.

Plastic ring sizers are a convenient and fairly accurate way to determine your ring size, especially when compared to the hassle of visiting a jeweller or the unreliability of printable paper sizers.

Measure with a tape measure

If you have access to a tape measure, you can measure your ring size at home. Here's how:

Wrap the tape measure around your finger

Take a tape measure and wrap it around the base of your finger. Make sure the tape measure is level and not twisted as you do this.

Note where the tape measure overlaps

Mark the point on the tape measure where it overlaps and crosses over itself with a pen. Make sure the pen mark is clear and easy to read.

Measure the tape measure

Now, stretch out the tape measure and use a ruler to measure its length in millimetres. This will give you the circumference of your finger.

Calculate the diameter

To get the diameter, divide the circumference by pi (3.14). This will give you the diameter of your finger.

Check a ring size chart

Use the ring size chart to compare the diameter of your finger to the standard ring sizes. Pick the closest measurement on the chart to find your ring size.

It's worth noting that your ring size may vary depending on the time of day and the temperature. Your fingers are smaller in the early morning and in cold weather, and larger when it's warm. It's a good idea to measure your ring size at the end of the day when your fingers are warm, and to measure a few times for accuracy.

Frequently asked questions